RFQ quoting for engineering firms
RFQ quoting automation for machine shops and fabricators
An RFQ and a drawing go in. A draft quote comes out, built from your own rates, materials and past jobs, for you to check and send.
01 What it does
From RFQ email to draft quote
This is what happens to one RFQ, step by step.
- It reads the RFQ and the drawing. Part number, revision, material, quantity (and any price breaks asked for), finish, tolerances and the delivery date wanted.
- It works out the route. The operations the part needs, from sawing through milling, turning, fabrication and inspection, plus any outside processing such as anodising, plating or heat treatment.
- It builds the numbers from your data. Setup and cycle time estimates from similar jobs you have run, your machine and labour rates, material at your supplier's price with stock size and offcuts, and your margin rules.
- It writes the draft quote in your format. With the assumptions written down, and anything it could not read or was unsure about flagged at the top.
- You check it and send it. You change what you want to change. Nothing goes to the customer until you say so.
02 Follow-ups
The chase that usually doesn't happen
Most quotes that go quiet were never chased. I set up follow-ups at the intervals you choose, for example a few days after sending and again a week or two later. They go from your email address, in your wording, and stop when the customer replies.
You can have each chaser queued for your approval, or let it go automatically for quotes under a value you set. Your call.
03 What I need from you
A small amount of your own data
To build a pilot
- Five to ten past RFQs, with the quotes you sent
- Your machine and labour rates
- Material supplier prices, or the sheet you quote from
- The outside processes you use and what they cost
- How you format a quote today
To try it first
- One recent RFQ and its drawing
- Anonymised if you prefer
- That is all. I'll make assumptions and list them, so you can see where your real data would change the answer.
Where it won't help much. One-off prototypes where every job is different, very large assemblies, and drawings I cannot read. If your RFQs look like that, I'll tell you on the call.
04 Questions
Common questions
Does this replace our estimator?
No. It does the reading and the first draft, and you do the judgement. Your estimator checks every quote, changes what needs changing and sends it. The aim is to cut the typing and the digging through old jobs, not to take the decision away.
What if the drawing is a poor scan?
Clean PDFs from a CAD system work best. Poor scans, hand sketches and large assemblies are harder. Send me one and I'll tell you honestly how well it reads before you spend anything.
Which systems does it work with?
I start from what you have: Excel price sheets, Sage, JobBOSS, or past quotes in a folder. Whether it can write back into your job system depends on that system. I'll say so plainly after I have seen how you work, and a draft quote you copy across is a fine starting point.
Who sees our drawings?
Only me, plus the tools I use to do the work, which I'll name before I process anything of yours. I'll sign an NDA first if you ask. The privacy page has the detail.
How long does a pilot take?
Usually two to three weeks for one workflow such as RFQ to draft quote. Setting up several connected workflows takes longer, typically four to eight weeks.
What does it cost?
A pilot starts from £1,500 and optional monthly support from £250 a month. The prices page has the full list.
01 Send me one RFQ
Send me one RFQ and I'll show you
Pick a recent RFQ, with the drawing. Anonymise the customer name if you like. I'll build a draft quote from it and send it back so you can judge it against what you would have quoted.
- It costs nothing and there is no obligation.
- I aim to reply within two working days.
- If you want an NDA signed first, say so and I'll do that before you send anything.
Easiest route: email it to vitalautomation@outlook.com with the drawing attached. Or use the form below.
Your message and any file go to me and are stored by Netlify, which hosts this site. See the privacy page. You can also email vitalautomation@outlook.com directly.
02 Or talk first
Book a 30-minute call
If you would rather talk it through first, pick a time. We'll go through how you quote today and whether automating it makes sense. If it doesn't, I'll say so.
Calendar not showing? Open it in a new tab or email vitalautomation@outlook.com.